Lesson 1 - Prep and Roughout Stage - How to Carve A Wood Spirit | Woodcarving Tutorial for Beginners

Lesson 1 of 5 In this Schaaf Tools Video Series, woodcarver Lucas Kost will take you through the process of carving a wood spirit from start to finish. In lesson 1, beginners will learn the answers to these questions: What tools do I need to carve a face? How do I set up and mount my project if I don't have a carving vise? How does Lucas approach bringing a face out of a piece of wood in the roughout stage? Video Notes What Tools Do I Need For This Type of Woodcarving? From the 12-Piece Foundation Set https://www.schaaftools.com/products/premium-hand-sharpened-schaaf-full-size-wood-carving-tools-set-of-12 #8-4mm #9-10mm #11-3mm From the 7-Piece Expansion Set https://www.schaaftools.com/products/premium-schaaf-full-size-wood-carving-tools-set-of-7-for-beginners-hobbyists-and-professionals #3- 20mm #11-15mm #12-10mm From the 4-Piece Fishtail Set https://www.schaaftools.com/products/premium-hand-sharpened-schaaf-tools-wood-carving-fishtail-set-for-detail-work-4pc #3F 6mm How Do I Mount My Project? Timestamp [1:11] - Simple Mounting System - Three 2x4s stacked on top of each other at the bottom - One 2x4 on top - One 2x6 perpendicular up the middle - Next, using screws attach your piece of carving wood to a separate 2x6 - With clamps, secure the second 2x6 (with your piece of carving wood) to the first 2x6 Types of Wood for Spirit Carving Timestamp [1:38] - Lucas uses cottonwood bark - Recommended if you can find it (often available for purchase online in the US and Canada) - If you don't have access to cottonwood bark, not a problem! Basswood, butternut, or any other type of material will work just fine, and the principles of face carving that Lucas is teaching are exactly the same. How Do I Approach Bringing A Face Out of a Piece of Wood? Step 1: Create a Rounded Surface Timestamp [2:20] - Use your Schaaf Tools #3-20mm Gouge - Clear away material to create a semi-rounded surface Step 2: Draw the Proportions Timestamp [2.56] - How to draw your guiding lines with marker to proportion to set up the face carving Step 3: Define the Eyeline Timestamp [4:00] - #11-15mm - Horizontal cut along the "eyeline" creating the eyebrow ridge at the top - Smaller, shorter cutting motions are recommended. You can always pass through a second time to take off more material Step 4: Roughing in the Nose Timestamp [4:41] - With the #11-15mm, clear away the material on either side of the nose, up to the eyebrow ridge Step 5: Taking the Forehead Down Timestamp [5:25] - Using the #3-20mm gouge, bring down the forehead below the nose material Step 6: Shaping the Nose Timestamp [6:05] - Identify where the tip of the nose is going to be and draw a circle to represent the ball of the nose - Using your #12 V parting tools, come underneath the nose and create a line to define where the bottom of the nose is going to b - Continue to clear away the material underneath using your larger #3- 20mm carving chisel - Next start to carve the angle of the nose - Draw in the lines to mark where the bridge of the nose is going to be Two Types of Cuts - The Sweeping Cut and the Plunge Cut Timestamp [8:20] - Learn how to do a sweeping cut to bring the bridge of the nose forward. This type of cut leaves a nice, clean transition out the other side of the cut. - The second way to do this is with a plunge cut. Insert the corner edge of the wood carving tool and cut along the line of the nose. Next, come in with a U shaped gouge, like the #9-10mm and clean up the plunge cut. Step 7: Roughing in the Mustache and Hair Timestamp: [9:27] - Draw in the shape of the wood spirit's mustache - To bring the mustache forward, carve around the outside lines with your #11-15mm, removing material below and above the mustache. The trusty #3-20mm gouge is helpful to do this as well. - Draw in the hairline next. You'll do the same thing you did with the mustache for the hair, removing material above and below the raised area that will be the hair. - Define your mustache better with your V-tool Step 8: Setting up the Eyes Timestamp [12:11] - We are going to carving open eyes. Draw two semicircles where the eyes will be -The eyes should be raised a bit, so you are going to leave the material inside the drawn semicircles - Begin the cuts with the #11-15mm. Be mindful of where the top edge of the tool is, and run the top edge alonf the pencil line to scoop out the area underneath the eye circle. IMPORTANT - be mindful not to take out any of the material inside the drawn semicircle. - With the #11-3mm gouge, make scooping cuts, coming down from above, to bring depth to the corners of the eye - Round out the eyeball area using one of your smaller fishtail gouges (NOTE - if you don't have a fishtail, you can use a skew chisel to this as well. And that wraps up part one of the video series on How to Carve a Wood Spirit! In step two, we'll start to work on the nose and eye-mounds.