XTOOL RA2 PRO In-Depth Setup Guide, Assembly, Examples, and RA2 Tilt Upgrade!

In this video I will take you in depth into getting started with the XTOOL RA2 PRO rotary attachment combined with the XTOOL D1 PRO! I will take you right from the unboxing all the way to the complete workflow of processing various rotary engraving jobs.

XTOOL sent me the D1 Pro 10W combined with the RA2 rotary tool to test and I've been genuinely impressed with the build quality of this laser cutter and the rotary tool. This is not a long term review, however, and the opinions expressed in this video are (at this point in time) more like first impressions. That being said, the apparent quality of the RA2 leads me to believe it will perform reliably over time. If anything changes, I will come back and update this video description to report my findings.

In addition to the setup guide, I have designed and made available two new modifications. First is the PCB and button cover as seen at the beginning of the video:

► https://embracemaking.com/products/xtool-d1-pro-pcb-and-button-cover-kit

The second is the RA2 riser and tilt mechanism. This tilt mechanism kit allows you to continuously adjust the position up to 40 degrees both ways. Other tilt kits on the market often just lift the metal base in one direction only by lifting the end of the base. This kit mounts the main assembly on top of the T-slot profile and allows you adjust the center of mass above the base so that there is no risk of the assembly tipping over:

► https://embracemaking.com/products/xtool-ra2-pro-tilt-mechanism-kit

I have also designed and made available a fume extractor nozzle to eliminate fumes at the source:

10W D1 Pro version:
► https://embracemaking.com/products/xtool-d1-pro-10w-fume-extraction-nozzle

20W D1 Pro version:
► https://embracemaking.com/products/xtool-d1-pro-20w-fume-extraction-nozzle

You can find the accessory snap latch case here:
► https://embracemaking.com/products/rugged-pelican-style-accessory-case

Always remember to practice proper laser safety. These lasers can seriously harm you directly (your eyes) or indirectly (your lungs and health). ALWAYS wear your safety glasses! By-products from processing certain materials can be toxic and harm you. DO NOT CUT vinyl materials like PVC. Check this list for hazardous materials before cutting something:

► http://wiki.atxhs.org/wiki/Laser_Cutter_Materials

If you are looking for products or items I've used with the D1 Pro in this video, see below. As an Amazon Associate may I earn from qualifying purchases (at no extra cost to you):

XTOOL D1 Pro 10W:
► https://www.xtool.com/products/portable-diode-laserbox-d1-for-laser-engraving-laser-cutting?ref=D5HpJRsyqyUUnt&utm_medium=null&utm_source=influencer

XTOOL D1 Pro 20W:
► https://www.xtool.com/products/portable-diode-laserbox-d1-for-laser-engraving-laser-cutting-b?ref=D5HpJRsyqyUUnt&utm_medium=null&utm_source=influencer

Alcohol Prep Pads (Clean Skin Oils Off Surface Before Engraving!)
► https://amzn.to/3hOSQ3s

Electric Screwdriver Kit
► https://amzn.to/3WhkTYk

Digital Measuring Calipers:
► https://amzn.to/3WddZnd

12 Inch Speed (Rafter) Square
► https://amzn.to/3PKvIjl

8 Pack Black Water Bottles
► https://amzn.to/3G8uQlr

12 Pack Black Wine Tumblers
► https://amzn.to/3FKrbZx

6 Pack Black Mugs With Handle
► https://amzn.to/3hJVGH8

3 Speed 90,000 RPM Electric Compressed Air Blower
► https://amzn.to/3jnfzEb

Laser Proof Silicone Work Surface Mat (20" x 28")
► https://amzn.to/3zDyMG7

Laser Proof Silicone Work Surface Mat (23.5" x 31.5")
► https://amzn.to/3A0Fzv1

If you want to go more in depth with the XTOOL Creative Space Software, check here:

https://support.xtool.com/hc/en-us/articles/6816833786519-Use-xTool-Creative-Space-XCS-to-Operate-xTool-D1-Pro

SAFETY WARNING: DO NOT CUT THESE MATERIALS:
► http://wiki.atxhs.org/wiki/Laser_Cutter_Materials

Thank you @xToollaser

0:00 Intro
1:17 Unboxing
2:46 PCB and Button Cover
3:52 RA2 Basic Setup
7:40 Cylindrical Objects on Parallel Rollers
11:30 Adjusting the Parallel Rollers
13:04 Roller Steady Rest
14:28 Installing the Rotary Chuck and Jaws
18:50 RA2 Tilt Mechanism Upgrade Installation
23:04 Setting Up Mug With Handle
24:52 Installing Extra Leg Extensions
26:11 Removing Laser Guard For Extra Clearance
27:40 Engraving Mug With Handle
31:31 Setting Up Objects With Tapers
33:56 Engraving Tapered Wine Tumbler
36:48 Setting Up Spherical Objects
38:50 Setting Up Rings (External)
39:20 Setting Up Rings (Internal)
40:45 Outro

#laser #ra2 #engraving

****************************************************************************

If you enjoy and have benefited from my content and are feeling generous I would love your support! You can "buy me a coffee" here:

► https://www.paypal.com/donate/?hosted_button_id=V2T6MEFUGP73Y

By supporting my channel you are encouraging me to continue with this time consuming endeavor.

Follow me on Instagram!

► https://www.instagram.com/embracemaking/